GENERAL SPECS
Air & Electrical Lines:
A split wire harness return ground system incorporates a modular PVC encased 14 ga. copper wiring, 12 volt system. Terminates on roadside of front panel with 7-way split-pin receptacle and fixed gladhands. Quick release style gladhand on blue service line. Air and electrical lines are run externally on front. Synflex air lines and electrical harness are routed along bottom rail above the crossmembers.
Floor:
1 3/8” full laminated oak flooring, pre-undercoated. Shiplap joints with crusher bead between floor board joints. Three (3) 5/16″ diameter torx head screws per each inner board and two (2) 5/16″ screws in each edge board.
Front Panel:
.048″ thick pre-painted white aluminum sheets with five (5) 1 5/16″ deep galvanized steel hat shaped posts. Aluminum three-piece front top rail with 4″ radius corner castings. Sheets fastened to posts with one (1) row of solid 3/16″ rivets on 2″ centers at seams and 4″ centers at intermediate locations. Foam sealing tape at all sheet seams.
Side Panels:
.048″ thick pre-painted white aluminum sheets with .625″ deep galvanized steel hat shaped posts on 24″ centers. Extra posts over kingpin and landing gear area. Sheets fastened to posts with one (1) row of solid 3/16″ rivets on 2″ centers at seams and 4″ centers at intermediate locations. Foam sealing tape at all sheet seams.
Bottom Rails:
8-3/4″ deep heavy extruded aluminum alloy 6061-T6 with floor sealing lip.
Top Rails:
5-9/16″ deep heavy duty extruded aluminum alloy 6061-T6.
Kingpin Structure:
3-1/8″ deep steel structure automatically welded. AAR tested and certified. 5/16″ thick formed channels welded to 5/16″ thick steel bottom plate. 5/16″ thick by full width front pick-up plate with turned up-lip. Kingpin is of crosshead design located 36″ back from front. Front wrap is shotblasted, primed, painted white and oven baked prior to installation. Strick uses a zinc epoxy primer with urethane top coat. Strick applies ECK corrosion barrier on king pin side plates and bottom rail.
Crossmembers:
4″ hot rolled steel ‘I’ beam on 12″ centers throughout. Steel end clips are pre-welded to crossmember ends. Crossmembers are coated with corrosion resistance copolymer prior to installation. Steel clip is separated by plastic tape from the aluminum bottom rail to prevent electrolysis. Strick applies ECK corrosion barrier on end caps on each cross member. Crossmembers attached with four (4) 3/8″ diameter solid rivets on each end.
Roof:
.040″ thick one-piece tensioned aluminum sheet. Full length aluminum edge strips rolled over top rail leg in rivet area. All fasteners outside of cargo area.
Roof Bows:
One-piece 1″ deep galvanized 16GA steel “spring type” on 24″ centers connected with two (2) huck bolts at ends and adhesive tape to roof sheet. Extra bow at rear to help with racking stability.
Rear Frame:
High tensile steel sections, fixture built, all welded construction. Protection from dock abuse is afforded through the sill section which recesses the lights within the sill. Heavy duty bumper features bolt-on perforated bumper tube with vertical gussets and ‘K’ bracing bolted to suspension structure and rear frame. Bumper conforms to CMVSS and FMVSS standards. Rubber dock bumpers installed between stop/tail/turn lights. Entire assembly is hot dipped galvanized. Easy access, removable bolt-on rear light rock guards.
Rear Doors:
Swing type, .5″ composite construction. Dual durometer seals. Pre-painted white galvanized steel exterior, pre-painted white galvanized steel interior. Five (5) aluminum hinges per door. One galvanized steel zero-torque locking bar with rubber grip handle per door. Door hardware is protected from electrolysis by foam gaskets. All fasteners are large head bolts. Chain type door holdback with chain in rail and hook on door.
Front Lining:
1/2″ thick structure wood installed full height, horizontally. Internal front corner protectors standard.
Front Scuff:
Non-galvanized 7GA X 12″ high flat steel scuff
Side Lining:
HDPE, snap in /snap out type, installed vertically between posts above scuff liner. No lining fasteners.
Side Scuff:
18 ga. x 12″ high galvanized corrugated 80psi steel with 1/4″ deep ribs fastened directly to posts.
Crashplate:
15″ smooth galvanized steel.
Sliding Subframe:
Variable position sliding tandem with full length bolt-on slide pads. Slide range from approximately 70″ to 174″. Tubular steel stop bars are welded in place front and rear with solid end bar inserts. Subframe is locked in place by four (4) self-locating spring loaded solid steel pins to insure positive engagement. There are four (4) bolt-on hold-down clamps for additional safety.